You press Start on the dishwasher control panel. You hear the drain pump hum for a minute. You wait for the familiar splash of water hitting the tub walls. Ten minutes later you open the door to a dry tub. The w11175771 water inlet valve is the part that lets water into the machine. Water Filters FAST lists it at $56.99 and it is in stock today.

A dishwasher that drains but never fills points directly at a failure in the water path. This single valve controls the flow of liquid from your house plumbing into the appliance tub. The machine expects water to arrive. The broken valve delivers nothing. The wash cycle continues running dry.

Written by the Water Filters FAST filter experts. Reviewed by Phil McNamara, owner, Water Filters FAST. Updated September 2026.

What the w11175771 valve does in your dishwasher

According to iFixit, this replacement part regulates the water intake for your dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. Household water pressure pushes water past the open valve and into the tub. The valve closes when the machine has enough water. The water stops flowing. This sequence repeats during every wash cycle and every rinse cycle.

The component sits at the very bottom of the appliance. You will find it located behind the lower kickplate panel. It sits in either the right or left corner. The kickplate comes off from the front, so the dishwasher stays in place under the counter.

Why the box might carry the older W10195047 part number

Appliance manufacturers frequently update parts to improve performance. Whirlpool redesigned the older W10195047 and W10327250 component. The company assigned the new design the part number W11175771. Water Filters FAST lists the part under the old number W10195047 and ships the redesigned W11175771. Both numbers refer to the same water path function.

The physical shape of the new design differs slightly from the old version. The new design no longer includes or requires the original mounting bracket. The updated valve mounts directly on the metal frame. You will simply attach the new valve straight to the dishwasher frame during installation. You discard the old metal bracket along with the broken valve.

According to iFixit, this component replaces five previous part numbers. The table below outlines the obsolete numbers and their current replacement status. You might pull an old valve out of your machine and see one of these old numbers stamped on the plastic. The label on the old part overrules any table. You should always read the plastic housing of your existing valve first.

Brands that share this whirlpool dishwasher water inlet valve

Whirlpool manufactured appliances for many different corporate brands over several decades. A single replacement part often fits multiple different machines in your kitchen. This exact part works directly with Whirlpool, Kenmore, KitchenAid, and Maytag appliances. It also fits certain Amana, Magic Chef, Inglis, and Crosley units.

Appliance companies frequently share components to reduce manufacturing costs. A factory produces one reliable valve design. Multiple brands then install that same part into their own chassis. This crossover makes finding replacement parts easier for homeowners. You can often fix a Kenmore machine using a part packed in a Whirlpool box. A Kenmore or Maytag dishwasher built by Whirlpool takes this same valve. You can browse the Whirlpool collection to see how parts cross over between brands.

According to iFixit, you must verify your device model number for compatibility before purchasing. The model number sticker sits on the door edge or the door frame on most dishwashers. You compare that model number against the accepted list for this valve.

Two free checks for a dishwasher not filling

A dishwasher that hums and drains but keeps the tub dry at the start of the cycle points at the water path. The machine attempts to pull water, but the plumbing delivers nothing. Before you buy a replacement valve, you should check two things that cost nothing. These two free checks take about two minutes.

A dry tub interrupts your evening routine. You expect clean dishes, but you find dirty plates and dried food. A quick diagnosis saves you a call to a repair technician. You can rule out simple user errors before you spend money on replacement parts. The two-minute check requires no tools and creates no mess.

First, open the cabinet under the sink and confirm the supply valve is fully open. A closed supply valve produces the same symptom as a broken inlet valve. If you need help identifying plumbing fixtures in that cabinet, you can review a recent Water Filters FAST post discussing under sink water lines for reverse osmosis systems.

Second, confirm the dishwasher door latch clicks shut. A dishwasher that thinks the door is open will never fill. Press the door firmly against the tub. Listen for a solid mechanical click. If both of these checks pass and the tub still stays dry, the inlet valve is the next part in the water path.

A failed fill cycle is one common symptom of a broken valve. iFixit lists a second symptom: a valve that leaks water onto the floor under the kickplate even when the dishwasher is off. A puddle near the right or left front corner points at the same part.

How to swap the valve behind the kickplate panel

You can complete this repair with common household hand tools. Working on appliance parts requires caution around standing water and electricity. Water Filters FAST offers this general safety advice for approaching the lower kickplate.

You do not need specialized plumbing knowledge to change this part. You unbolt the broken unit and bolt the new unit in its place. The photograph you take on your phone serves as your personal wiring diagram. You match the physical connections to the picture.

1. Unplug the dishwasher power cord or switch off the kitchen circuit breaker.
2. Close the water supply valve located under the kitchen sink.
3. Remove the lower kickplate panel to expose the bottom of the appliance.
4. Find the existing valve in either the right or left corner of the frame.
5. Photograph the hose and wire connections before touching anything on the old part.
6. Disconnect the old component from the frame and the plumbing lines.
7. Swap the new valve onto the frame using the direct mount design.
8. Connect the water lines and electrical wires based on your photograph.
9. Restore power to the kitchen and open the under sink supply valve.
10. Run a brief rinse cycle and watch for a successful fill.

Common questions about the dishwasher inlet valve

Is W11175771 the same as W10195047?

Whirlpool redesigned the older W10195047 valve. The company assigned the new updated design the W11175771 part number. Water Filters FAST lists the part under the older number and ships the redesigned valve.

Does it fit a Kenmore dishwasher?

This exact part fits many Kenmore dishwashers manufactured by Whirlpool. Verify your specific appliance model number before purchasing. You can find the model number sticker on the door edge or the door frame.

Where is the inlet valve on a Whirlpool dishwasher?

This water inlet valve is located directly behind the lower kickplate panel. You will find it mounted in either the right or left corner. You access it entirely from the front of the appliance.

What happens when the inlet valve fails?

A failed valve prevents the dishwasher from filling with water. The cycle starts and the drain pump hums, but the tub remains dry. A broken valve can also leak water onto the kitchen floor even when the machine is turned off.

Does the new valve need the old mounting bracket?

The new component design no longer includes or requires the original mounting bracket. The updated valve mounts directly on the appliance frame. You discard the original metal bracket along with the broken valve.

How do I know the valve is the problem?

A dry tub at the start of a cycle points to a water path issue. You can check the under sink supply valve and the door latch for free in two minutes. If the supply is open and the door is latched shut, a dry tub points at a failed inlet valve.

Order your new dishwasher water valve today

Water Filters FAST stocks the W11175771 dishwasher inlet valve today. You can fix a dishwasher not filling and restore your daily kitchen routine. Water Filters FAST lists it at $56.99 for a single unit. This component lives in the main valves collection alongside other major appliance parts.

Shipping is free over $75, and orders under that carry a $5 flat rate. A 30-day return policy and the Water Filters FAST satisfaction guarantee back every order. Call 855-789-FAST and the filter experts will confirm the match before you buy.